vehicle display controller ? three confgurations - optical rotary encoder - encoder with pushbutton - joysticking encoder with pushbutton ? j1939 and canopen versions ? dimmable led indicators and legends ? sealed to ip67 ? vibration and impact resistant ? operating temp: -40 o c to +85 o c ? long life: 500,000 cycles ? support for multiple key combinations ? designed for 12/24 volt systems ? custom legends and confgurations dimensions in inches (and millimeters) www.grayhill.com put display functions within reach - 5 hot keys for rapid navigation - scroll with rotary encoder - select with pushbutton - navigate with joystick rotary encoder version with target legends joysticking encoder version your experts in cab controls grayhill specializes in the design, development and production of human interface controls, including: - cab user interface design - customized control panels - can-bus interface devices esc blank keys shown below iso symbols shown below recommended panel cut-out
custom options available contact grayhill or your local grayhill sales representative for more information. environmental specifications operating temperature ansi/asae ep455 5.1.1 level 2 -40c for 4 hours to +85c for 11 hours storage temperature ansi/asae ep455 5.1.2 level 2 -40c 4 hours to +85c 4 hours thermal shock ansi/asae ep455 5.1.3 -40c to 70c at a rate of 4c/ min (1 hour at extremes) altitude (barometric pressure) ansi/asae ep455 5.2 101.3kpa to 18.6kpa sand and dust ansi/asae ep455 5.3 24 hours with 0.88g/m3 solar radiation ansi/asae ep455 5.4 43 to 75w/m2 uv radiation (280 to 400nm wavelength) for 300h wash down ansi/asae ep455 5.6 level 2 375 kpa and 8.3 l/min for 10 minutes @15c water temp ingress protection ip67 1 meter submersion for 30 minutes humidity ansi/asae ep455 5.13 96% humidity at 35c for 240 hours. salt fog ansi/asae ep455 5.9 5% aqueous solution of nacl @ 35c and a ph between 6.5 and 7.2 for 48 hours chemical resistance (resis - tance to solvents) iso 16750-5 ep 455 (5.8.2) thermal cycling (change of temperature) iso 16750-4 -40 to 85c 2 hours at extremes change rate = 1c/ min (8 hours) repeat for 30 cycles. mechanical performance vibration, random ansi/asae ep455 5.15.1 2 hours each axis @ 52.4 m/s2 rms overall acceleration and spectral power density of 2m2/s3 from 50hz to 2000hz vibration, sinusoidal ansi/asae ep455 5.15.2 a logarithmic sweep from 10hz to 2000hz to 10hz over a period of 20 minutes for 4 hours in each of 3 orthogonal axes with amplitude of 1.5mm from 10hz to 40hz and a constant acceleration of 35m/s2 rms from 40hz to 2000hz. shock / crash safety ansi/asae ep455 5.14 a single 11ms half sine pulse of 490 m/s2 in 3 perpendicular axes. drop ansi/asae ep455 5.14.2 level 1 drop component 400 mm onto a hardwood benchtop on all practical edges. shipping integrity international safe transit agency procedure 3a electromagnetic compatibility specifications esd ansi/asae ep455 5.12 +/- 25kv for 10 pulses, 5 of each polarity radiated immunity iso14982 6.6 10mhz-1000mhz range 48ma bulk current injection 100v/m conducted emissions sae j1113-41 class 3 broadband radiated emissions iso14982 6.4 64db to 54db, 30mhz-75mhz (linearly decreases) 54db to 65db, 75mhz-400mhz (linearly increases) 65db, 400mhz- 1000mhz electrical performance specifications maximum load ansi/asae ep455 5.1.1 level 2 -40c 4 hours +85c for 11 hours max load applied jump start forward voltage iso 16750-2 36v for 60 minutes jump start reverse voltage iso 16750-2 -36v for 60 minutes short circuit protection iso 16750-2 all outputs to ground for 60s reverse polarity protection iso 16750-2 28v for 60s starting profle iso 16750-2 class a battery-less operation ansi/asae ep455 5.11.3 level 2 apply 6+12.6sin(2*pi*f*t) f is swept from 500hz to 1.5khz 5min load dump iso 7637-2 test pulse 5b class a switching spikes C negative iso 7637-2 test pulse 3a class a switching spikes C positive iso 7637-2 test pulse 3b class a wire harness inductance iso 7637-2 test pulse 2a and 2b class a +/- inductive load pulse ansi/asae ep455 5.11.4 14-300e^(-t/.001)v 1hz for 300 cycles +/- mutual coupling ansi/asae ep455 5.11.6 level 2 14+200e^(-t/14x10^-6)v 1hz for 300 cycles alternator feld decay ansi/asae ep455 5.11.2 class a ce compliance agriculture and forestry machinery emc iso 14982 esa construction machinery emc en 13309:2000 esa bulletin 1124 rev 04/12 pin 1 2 3 4 signal power gnd can_h can_l connection 4 pin deutsch dt connector. power with 8v to 32v vehicle type inputs. ordering information www.grayhill.com grayhill, inc. 561 hillgrove avenue phone: (708) 354-1040 lagrange, illinois 60525 fax: (708) 354-2820 3jxxx5-200n series code keypad symbols 0 = blank 1 = iso symbols (as shown in dimensional drawing) 2 = targets input type 0 = encoder 1 = joystick encoder protocol blank = j1939 n = canopen custom designation 200 = default center pushbutton 0 = no pushbutton 1 = pushbutton (joystick always has pushbutton) configuration 5 = default mounting info use m6 nut (1mm pitch) max torque 25 in-lbs
|
